brake pads RENAULT TWINGO RS 2009 2.G Chasiss ESP Workshop Manual

38C-26
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF007
CONTINUED 2
If the air gap is correct:
–Swap both rear wheel brake discs as well as the brake pads.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF007 has become DF027 Rear right-hand wheel speed sensor circuit,
replace the instrumented bearing/wheel sensor mounting assembly (see MR 411, Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
–If the fault remains on the same side, replace component 151 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Rear wheel speed sensor, Removal - Refitting).
For versions equipped with drum brakes:
–Swap both rear wheel brake drums.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF007 has become DF027 Rear right-hand wheel speed sensor circuit, replace
the target (see MR 411, Mechanical, 33A, Rear axle components, Rear brake drums, Removal - Refitting).
–If the fault remains on the same side, replace component 151 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Rear wheel speed sensor, Removal - Refitting).

38C-33
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF027
CONTINUED
2.DEFNOTESConditions for applying the fault finding procedure to
stored faults:
The fault is declared present after a road test.
Check the connection and condition (possible wiring damage) of the connectors ofcomponents 1 094and150.
Iftheconnector is faulty (seeTe chnical Note 6015A, Repairing e lectrical wiring, Wiring: Precautions for repair),
repair the connector, otherwise replace the wiring.
Ch eck the insulation and continuity ofconnections 4Sand4Tbetweencomponents 150and1094.
Alsocheckthe insulationbetween these 2 connections.
Iftheconnection or connections are faulty (seeTe chnical Note 6015A, Repairing e lectrical wiring, Wiring:
Precautions for repair), repair the wiring, otherwise replace it.
Inspect the condition of the target ( metallic contamination etc.).
Cleanthetarget with compressed air if necessary.
For v ersions e quippedwithdiscbrakes:
Check the sensor/target air gap through one wheel revolution (0.1 mm<rearwheel air gap <0.9 mm).
If the air gap isincorrect:
–Replace the instrumented bearing/wheel sensor mounting assembly (see MR 411, Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
If the air gap iscorrect:
–Swap both rear wheel brake discs as well as the brake pads.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF007 Rear left-hand wheel speed sensor circuit has become DF027, replace
the instrumented bearing/wheel sensor mounting assembly (see MR 411, Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
–If the fault remains on the same side, replace component 150 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Rear wheel speed sensor, Removal - Refitting).
For v ersions e quippedwithdrumbrakes:
–Swap both rear wheel brake drums.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF007 Rear left-hand wheel speed sensor circuit has become DF027, replace
the target (see MR 411, Mechanical, 33A, Rear axle components, Rear brake drums, Removal - Refitting).
–If the fault remains on the same side, replace component 150 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Rear wheel speed sensor, Removal - Refitting).

38C-42
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF090
PRESENT
OR
STOREDFRONT RIGHT-HAND WHEEL TARGET
NOTESPriorities when dealing with a number of faults:
Deal with fault DF026 Front right-hand wheel speed sensor circuit first if it is
present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test.
Visually inspect the condition of the axle assemblies (impacts, deformations etc.) and the conformity and good
condition of the tyre mountings (see MR 411, Mechanical, 35A, Wheels and tyres, Tyres, Identification
and Tyre pressure, Identification).
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in good
condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor/target air gap through one wheel revolution (0.4 < front wheel air gap < 1.7 mm).
If the air gap is incorrect:
–Replace the instrumented bearing/wheel sensor mounting assembly if necessary (see MR 411, Mechanical,
31A, Front axle components, Hub carrier bearing: Removal - Refitting).
If the air gap is correct.
–Swap both front wheel speed sensors.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF090 has become DF091 Front left-hand wheel target, replace the magnetic
target (see MR 411, Mechanical, 31A, Front axle components, Front hub carrier bearing: Removal –
Refitting).
–If the fault remains on the same side, replace component 152 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Front wheel speed sensor, Removal - Refitting).
ESP_V05_DF090

38C-43
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF091
PRESENT
OR
STOREDFRONT LEFT-HAND WHEEL TARGET
NOTESPriorities when dealing with a number of faults:
Deal with fault DF006 Front left wheel speed sensor circuit first if it is present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test.
Visually inspect the condition of the axle assemblies (impacts, deformations etc.) and the conformity and good
condition of the tyre mountings (see MR 411, Mechanical systems, 35A, Wheels and tyres, Tyres,
Identification and Tyre pressure, Identification).
Replace the tyre(s) if necessary (see MR 411, Mechanical, 35A, Wheels and tyres, Tyres, Removal - Refitting).
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in good
condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
Check that the wheel speed sensor mounting is in good condition.
Check the sensor/target air gap through one wheel revolution (0.4 < front wheel air gap < 1.7 mm).
If the air gap is incorrect:
–Replace the instrumented bearing/wheel sensor mounting assembly if necessary (see MR 411, Mechanical,
31A, Front axle components, Hub carrier bearing: Removal - Refitting).
If the air gap is correct.
–Swap both front wheel speed sensors.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF091 has become DF090 Front right-hand wheel target, replace the magnetic
target (see MR 411, Mechanical, 31A, Front axle components, Front hub carrier bearing: Removal –
Refitting).
–If the fault remains on the same side, replace component 153 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Front wheel speed sensor, Removal - Refitting).
ESP_V05_DF091

38C-44
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF092
PRESENT
OR
STOREDREAR RIGHT-HAND WHEEL TARGET
NOTESPriorities when dealing with a number of faults:
Deal with fault DF027 Rear right-hand wheel speed sensor circuit first if it is present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test.
Visually inspect the condition of the axle assemblies (impacts, deformations etc.) and the conformity and good condition
of the tyremountings (seeMR 411, Mechanical systems, 35A, Wheels and tyres, Tyres, IdentificationandTy re
pressure, Identification).
Re place the tyre(s) if necessary (seeMR 411, Mechanical, 35A, Wheels and tyres, Tyres, Removal - Refitting).
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in good
condition.
ESP_V05_DF092

38C-45
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF092
CONTINUED
Check that the wheel speed sensor mounting is in good condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
For versions equipped with disc brakes:
Check the sensor/target air gap through one wheel revolution (0.1 < rear wheel air gap < 0.9 mm).
If the air gap is incorrect:
–Replace the instrumented bearing/wheel sensor mounting assembly (see MR 411, Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
If the air gap is correct.
–Swap both rear wheel brake discs as well as the brake pads.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF092 has become DF093 Rear left-hand wheel target, replace
the instrumented bearing/wheel sensor mounting assembly (see MR 411 Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
–If the fault remains on the same side, replace component 150 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Wheel speed sensor, Removal - Refitting).
For versions equipped with drum brakes:
–Swap both rear wheel brake drums.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF092 has become DF093 Rear left-hand wheel target, replace the target
(see MR 411, Mechanical, 33A, Rear axle components, Rear brake drums, Removal - Refitting).
–If the fault remains on the same side, replace component 150 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Rear wheel speed sensor, Removal - Refitting).

38C-46
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF093
PRESENT
OR
STOREDREAR LEFT-HAND WHEEL TARGET.
NOTESPriorities when dealing with a number of faults:
Deal with fault DF007 Left rear wheel speed sensor circuit first if it is present.
Conditions for applying the fault finding procedure to stored faults:
The fault is declared present during a road test.
Visually inspect the condition of the axle assemblies (impacts, deformations etc.) and the conformity and good
condition of the tyre mountings (see MR 411, Mechanical systems, 35A, Wheels and tyres, Tyres,
Identification and Tyre pressure, Identification).
Replace the tyre(s) if necessary (see MR 411, Mechanical, 35A, Wheels and tyres, Tyres, Removal - Refitting).
Check that the braking system (condition of brake pads, sealing, sticking, bleed, bearing clearance, etc.) is in good
condition.
ESP_V05_DF093

38C-47
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool
If the fault is still present, contact the Techline.
V3 MR-413-X44-38C050$101.mif
ANTI-LOCK BRAKING SYSTEM
Fault finding – Interpretation of faults38C
Bosch 8.1 ESP
Vdiag No.: 05
DF093
CONTINUED
Check that the wheel speed sensor mounting is in good condition.
Visually inspect the condition of the target (for clogging, metallic contamination, bearing grease, etc.) and clean
using compressed air if necessary.
For versions equipped with disc brakes:
Check the sensor/target air gap through one wheel revolution (0.1 < rear wheel air gap < 0.9 mm).
If the air gap is incorrect:
–Replace the instrumented bearing/wheel sensor mounting assembly (see MR 411, Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
If the air gap is correct.
–Swap both rear wheel brake discs as well as the brake pads.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the fault initially declared as DF093 has become DF092 Rear right-hand wheel target, replace
the instrumented bearing/wheel sensor mounting assembly (see MR 411 Mechanical, 33A, Rear axle
components, Rear hub carrier bearing: Removal - Refitting).
–If the fault remains on the same side, replace component 151 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Wheel speed sensor, Removal - Refitting).
For versions equipped with drum brakes:
–Swap both rear wheel brake drums.
–Clear the computer fault memory.
–Carry out a road test followed by another check with the diagnostic tool.
–If the initially declared fault DF093 became DF092 "Rear right-hand wheel target " , replace the target
(see MR 411 Mechanical system, 33A, Rear axle components, Rear brake drums, removal-refitting).
–If the fault remains on the same side, replace component 151 (see MR 411, Mechanical, 38C, Anti-lock
braking system, Rear wheel speed sensor, Removal - Refitting).